169 lines
4.8 KiB
Markdown
169 lines
4.8 KiB
Markdown
# DHT11 Temperature & Humidity Sensor for ESP32-C3
|
|
|
|
ESP-IDF project that reads temperature and humidity data from a DHT11 sensor and prints it to the serial console.
|
|
|
|
## Overview
|
|
|
|
This project reads data from a **DHT11** digital temperature and humidity sensor using the ESP32-C3 microcontroller. It implements the DHT11 communication protocol in software, reads sensor values every 5 seconds, validates the checksum, and displays:
|
|
|
|
- Current date and time (derived from compile time)
|
|
- Chip information (model, cores, features, flash size, silicon revision)
|
|
- Humidity percentage with 1 decimal place
|
|
- Temperature in Celsius with 1 decimal place
|
|
- Checksum validation status
|
|
|
|
## Hardware Requirements
|
|
|
|
| Component | Details |
|
|
|-----------|---------|
|
|
| Microcontroller | ESP32-C3 |
|
|
| Sensor | DHT11 (AM2302) |
|
|
| Connection | Single wire + pull-up resistor |
|
|
| Data Pin | **GPIO 0** (configurable in `main/main.c`) |
|
|
| Resistor | 4.7kΩ - 10kΩ pull-up between VCC and DATA |
|
|
|
|
### Wiring Diagram
|
|
|
|
```
|
|
DHT11 ESP32-C3
|
|
VCC ------ 3V3
|
|
DATA ----- GPIO0
|
|
GND ------ GND
|
|
```
|
|
|
|
Add a **4.7kΩ pull-up resistor** between VCC and DATA pin.
|
|
|
|
## Supported Targets
|
|
|
|
| ESP32 | ESP32-C2 | ESP32-C3 | ESP32-S2 | ESP32-S3 |
|
|
| ----- | -------- | -------- | -------- | -------- |
|
|
| ❌ | ❌ | ✅ | ❌ | ❌ |
|
|
|
|
## Project Structure
|
|
|
|
```
|
|
dht11_reader/
|
|
├── CMakeLists.txt # Project configuration
|
|
├── sdkconfig # Build configuration
|
|
├── main/
|
|
│ ├── CMakeLists.txt # Main component configuration
|
|
│ └── main.c # Application source code
|
|
└── README.md # This file
|
|
```
|
|
|
|
## Setup & Build
|
|
|
|
### Prerequisites
|
|
|
|
- [ESP-IDF v6.0](https://docs.espressif.com/projects/esp-idf/en/v6.0/esp32c3/get-started/index.html)
|
|
- RISC-V toolchain (riscv32-esp-elf)
|
|
- Python 3.13+ with virtual environment
|
|
|
|
### Build Instructions
|
|
|
|
```bash
|
|
# Activate ESP-IDF environment
|
|
source "$HOME/.espressif/tools/activate_idf_v6.0.sh"
|
|
|
|
# Navigate to project
|
|
cd temperature_measure
|
|
|
|
# Build the project
|
|
idf.py build
|
|
|
|
# Flash to device (replace PORT with your serial port)
|
|
idf.py -p /dev/ttyUSB0 flash monitor
|
|
```
|
|
|
|
## Configuration
|
|
|
|
The DHT11 data pin is defined in `main/main.c`:
|
|
```c
|
|
#define DHT11_GPIO 0
|
|
```
|
|
|
|
To use a different GPIO, change this define and rebuild.
|
|
|
|
### Reading Interval
|
|
|
|
The sensor is read every 5 seconds:
|
|
```c
|
|
vTaskDelay(pdMS_TO_TICKS(5000));
|
|
```
|
|
|
|
Note: DHT11 requires at least 1 second between readings. Adjust as needed.
|
|
|
|
## How It Works
|
|
|
|
### DHT11 Communication Protocol
|
|
|
|
1. **Start Signal**: MCU pulls DATA line low for 20ms, then high
|
|
2. **Sensor Response**: DHT11 pulls line low for ~80μs, then high for ~80μs
|
|
3. **Data Transmission**: 40 bits of data (5 bytes) in the following format:
|
|
- Byte 0: Humidity integer part
|
|
- Byte 1: Humidity decimal part
|
|
- Byte 2: Temperature integer part
|
|
- Byte 3: Temperature decimal part
|
|
- Byte 4: Checksum (sum of bytes 0-3)
|
|
|
|
4. **Bit Encoding**: Each bit starts with a ~50μs low pulse:
|
|
- `0`: ~26-28μs high pulse
|
|
- `1`: ~70μs high pulse
|
|
|
|
### Checksum Validation
|
|
|
|
The checksum byte should equal the sum of the first 4 data bytes. If validation fails, the reading is retried after 1 second.
|
|
|
|
## Output Example
|
|
|
|
```
|
|
Time: 2024-04-24 22:30:00
|
|
This is esp32c3 chip with 1 CPU core(s), WiFi/BLE, silicon revision v0.4, 4MB embedded flash
|
|
Minimum free heap size: 283488 bytes
|
|
Humidity: 45.2%
|
|
Temperature: 23.5°C
|
|
Checksum valid: Yes
|
|
```
|
|
|
|
## Troubleshooting
|
|
|
|
### Common Issues
|
|
|
|
| Issue | Solution |
|
|
|-------|----------|
|
|
| No sensor readings / checksum fails | Check wiring: DATA to GPIO0, pull-up resistor present |
|
|
| Build fails with missing component | Run `idf.py fullclean` then rebuild |
|
|
| `driver/gpio.h` not found | Ensure `esp_driver_gpio` is in PRIV_REQUIRES |
|
|
| Linker errors with `.riscv.attributes` | Your toolchain may be too new; use ESP-IDF 6.0 compatible version |
|
|
|
|
### Debug Mode
|
|
|
|
To enable debug output:
|
|
```bash
|
|
idf.py monitor
|
|
```
|
|
|
|
### Hardware Connection Check
|
|
|
|
Verify your wiring with a multimeter:
|
|
- GPIO0 should read HIGH when idle (via pull-up)
|
|
- 3V3 is supplying power
|
|
- GND is properly connected
|
|
|
|
## Technical Details
|
|
|
|
- **Sensor Range**: 0-50°C temperature, 20-90% humidity
|
|
- **Accuracy**: ±1°C temperature, ±1% humidity
|
|
- **Sampling Rate**: 1Hz maximum (1 reading per second)
|
|
- **Resolution**: 1° C, 1% humidity
|
|
|
|
## License
|
|
|
|
This project is provided under the **CC0-1.0** license (public domain). See the SPDX identifier in the source file.
|
|
|
|
## Resources
|
|
|
|
- [DHT11 Datasheet](https://www.mouser.com/datasheet/2/718/DHT11-Technical-Data-Sheet-Translated-Version-1137654.pdf)
|
|
- [ESP32-C3 Documentation](https://docs.espressif.com/projects/esp-idf/en/latest/esp32c3/)
|
|
- [ESP-IDF Programming Guide](https://docs.espressif.com/projects/esp-idf/en/latest/esp32c3/api-guides/index.html)
|